Trục truyền động cho máy cán phôi thô và phôi vụn

NETHERLANDS HEAVY INDUSTRY EDITION

HÃY LIÊN HỆ NGAY

THAM SỐ HIỂN THỊ

The Operational Reality in IJmuiden

The primary rolling stage, involving blooming and roughing mills, represents the most mechanically violent phase in the entire steel production hierarchy. In the integrated steelworks of the Netherlands, particularly in the heavy industrial zones near the North Sea Canal, drive shafts must translate the immense power of megawatt-class DC motors into the work rolls that reduce substantial ingots into blooms or slabs. This process is defined by the “bite”—the exact moment the steel enters the roll gap—which generates a torsional shock wave that can exceed 300% of the nominal torque rating within milliseconds.

Furthermore, the transition towards “Green Steel” in the Netherlands implies processing harder, advanced high-strength steel (AHSS) grades, which places even higher stress loads on the drivetrain. Standard universal joint shafts often succumb to low-cycle fatigue failure at the flange interface or brinelling of the cross bearings due to the constant reversing loads typical of a 2-High reversing stand. The saline atmosphere of coastal Dutch plants further accelerates corrosion fatigue, necessitating a radical rethink of material science and sealing technology.

The Ever-Power “Titan-Series” Response

To counter these extreme conditions, Ever-Power has engineered the Titan-Series Roughing Mill Spindles. Unlike conventional welded designs, our ultra-heavy-duty shafts feature a monolithic, forged yoke construction utilizing vacuum-degassed 18CrNiMo7-6 steel. This metallurgy provides a core toughness capable of absorbing the kinetic energy of the “impact bite” while maintaining a surface hardness of HRC 60+ to resist wear on the trunnions.

Our design philosophy aligns strictly with the safety coefficients mandated by NEN-EN 13001 and ISO 12100 for heavy lifting and rotational machinery. We incorporate a proprietary “Elastic Damping Spline” system which allows for micro-axial movement under load, preventing the transmission of axial thrust back into the motor bearings or pinion stand. This feature is critical for the longevity of the entire drivetrain in the Dutch metallurgy sector, where equipment availability is directly linked to competitive advantage in the European market.

Case Study: Rotterdam Port Area

Eliminating Spline Fretting on a 4-High Roughing Stand

Thử thách: A specialized rolling mill in the Europoort region was suffering from chronic spline fretting on their main roughing stand drives. The frequent reversing cycles (up to 12 times per minute) combined with the saline coastal air caused the slip splines to seize, transmitting massive axial loads into the motor bearings.

Giải pháp Ever-Power: We replaced the standard OEM shafts with our Titan-Series 5500. Key upgrades included a specialized Molybdenum-Disulfide/Nylon 11 composite coating on the male splines to lower the friction coefficient and a “Viton-Shield” sealing system to prevent salt ingress.

Tác động: Since installation in early 2024, the mill has operated for 18 months without a single driveline-related stoppage. Vibration levels dropped by 35%, and the customer reports an annual maintenance saving of €150,000.

ĐỌC BÁO CÁO KỸ THUẬT

Thứ hạng	Nhà sản xuất	Trụ sở chính	Năng lực cốt lõi
1	Voith Turbo	Đức	High-Performance Spindles
2	GWB (Dana)	Đức	Heavy Duty Cardan Shafts
3	Hệ thống truyền động Ever-Power	Trung Quốc (Toàn cầu)	Giải pháp luyện kim theo yêu cầu
4	Điện Maina	Ý	Gear Couplings & Spindles
5	Tập đoàn HZPT	Trung Quốc	Truyền tải điện công nghiệp
6	GKN Off-Highway	Vương quốc Anh	Integrated Powertrains
7	Gewes	Đức	Trục ổ bi lăn
8	Hệ thống truyền động EP	Trung Quốc	Heavy Duty Gearboxes
9	Tập đoàn Welte	Đức	Compact Drivelines
10	Tập đoàn Elbe	Đức	Kỹ thuật chính xác

Spline seizure in reversing mills is typically caused by high axial forces combined with inadequate lubrication. To prevent this, we recommend upgrading to shafts with Molybdenum Disulfide coated splines and ensuring your maintenance schedule includes high-pressure greasing with Calcium Sulfonate lubricants, which resist water washout and high loads typical in IJmuiden steelworks.

Yes, our Titan-Series shafts are fully customizable. We can manufacture flanges with precise Hirth serrations (e.g., diameters up to 1200mm) that perfectly match the output shafts of SMS Group, Danieli, or Primetals gearboxes, ensuring seamless torque transfer and eliminating bolt shear risks.

While standard OEM lead times can exceed 6 months, Ever-Power utilizes a dedicated heavy-forging supply chain. We can typically manufacture and deliver a custom 5,000 kNm shaft to the Port of Rotterdam in approximately 8-10 weeks, depending on the complexity of the heat treatment required.

Absolutely. Our drive shafts are designed with a safety factor >2.5, adhering to the Machinery Directive 2006/42/EC and NEN-EN 13001. We provide comprehensive documentation, including 3.1 Material Certificates and Ultrasonic Test reports, to support your compliance with the Dutch Working Conditions Act (Arbowet).